So I know my setup is really niche, but here goes nothing
- I am using Arch Pi on Pi 4
- Installed
cage
as a lightweight Wayland compositor - Installed
mpv + wireplumber + pipewire
I am not quite sure how to use cage
to launch a simple “Wayland session (if it even makes sense)”, so that I can send MPV to that display.
So I tried cage -s alacritty :1
, and it does launch alacritty
with it detecting that it is on wayland
.
But when I do DISPLAY=:1 mpv ....
, the video runs, but there’s no audio.
Also there’s no errors shown on mpv
either.
The other thing of note is that I tried cage -s Xwayland :1
and the audio+video works perfectly.
So in all:
- How do I launch
cage
to spawn a simple Wayland session? Is this even possible? - How do I solve the audio issue on Wayland?
EDIT: Thanks all for the help.
After some investigation, I found out the pipewire
somehow is not ran on startup of alacritty
, but it did for Xwayland
.
I noticed that the first play of the video would be audio-less on alacritty
, and subsequent ones are fine.
It seems like the first run causes pipewire
to be started and thus I wrongfully assumed that the daemon was running.
Still strange nonetheless…
It’s possible you didn’t install pipewire-audio, or didn’t start/enable a service.
Btw fun fact: you can use
mpv --gpu-context=drm
in a tty to watch a video directly from the framebuffer.Edit: read this https://wiki.archlinux.org/title/PipeWire#Audio
That shouldn’t be the problem since I’m using
pipewire
and it is working in the Xwayland session. When I launch intoalacritty
, I also checked thatpipewire + wireplumber
were both active
Have you tried with a different compositor first to rule out whether cage is the issue? For example try sway.
I tried with
cage + Xwayland
and that works perfectly, so I highly doubt that is the issue. Maybe it is something to do withcage + alacritty
that is causing it, but I’m not too well versed in the Wayland stuff to know if spawning a terminal application may somehow not support audio.Like I said we should try a different compositor just to rule it out.
I imagine these are two separate issues. I’ll attack the audio as I don’t know much about cage, albeit, are you running it from a tty on login or do you have a display manager (e.g. gdm, sddm)
Can you dump your installed packages with pacman -Qe and post it here? I’ll compare it to mine.
My audio setups have been pretty… interesting in the past. Normally, I prefer to do everything in the terminal, but pavucontrol can be pretty handy.
Other than that, you might try reading the man page for pactl.
are you running it from a tty on login
Yea, directly on
tty
.I imagine these are two separate issues.
I’d think they are related since
mpv
is working fine onXwayland
but not when I launchalacritty
insteadCan you dump your installed packages with pacman -Qe and post it here? I’ll compare it to mine.
alacritty 0.12.2-1 ani-cli 4.6-1 archlinuxarm-keyring 20140119-2 base 3-1 base-devel 1-1 bat 0.23.0-3 cage 0.1.5-1 dhcpcd 10.0.2-1 dialog 1:1.3_20230209-1 linux-rpi 6.1.54-1 lobster 4.0.0-1 man-db 2.11.2-1 neovim 0.9.1-1 net-tools 2.10-2 netctl 1.28-2 noto-fonts 1:23.9.1-1 opendoas 6.8.2-1 openssh 9.4p1-4 pacman-contrib 1.9.1-1 raspberrypi-bootloader 20230921-1 raspberrypi-firmware 20230921-1 ripgrep 13.0.0-3 socat 1.7.4.4-1 tmux 3.3_a-7 vi 1:070224-6 which 2.21-6 wireless-regdb 2023.09.01-1 wireless_tools 30.pre9-3 wpa_supplicant 2:2.10-8 xorg-xwayland 23.2.1-1
Seems like a pretty minimal config. I can respect that. Have you tried running with a display manager? E.g. sddm. They will often start with additional options you wouldn’t have starting from tty.
If sddm does work, you can cat /etc/sddm.conf I believe to see the options it uses and use those when you start from tty
For the audio, try installing pipewire-pulse
Finally, arch for arm isn’t officially supported. Your issues could stem from that. You might consider playing around in a VM with both versions to see if you can reproduce your problem.