I have my home network behind a wireguard VPN connection. The wireguard “server” is run on a debian computer and the home network is handled by an opnsense computer.

Edit: opnsense does DHCP but a switch does the actual local routing, so opnsense isn’t involved in 10.0.66.XXX <-> 10.0.69.XXX comms.

My home network is on the subnet 10.0.69.XXX, while the VPN connection gets the subnet 10.0.66.XXX.

Weirdly, this setup worked fine until yesterday for the PS Remote Play app (hard requirement, iOS device). Nothing changed as far as I can tell - but yesterday the PS4 stopped being found by the PS Remote Play app (when I’m home on the 10.0.69.XXX subnet, the PS Remote Play app works fine).

I suspect from what I can google ( https://www.snbforums.com/threads/ps4-remote-play-over-vpn.60629/ , https://github.com/williampiat3/ImprovingPSRemotePlay#longer-and-more-complex-solution ) that to make it seem to the PS Remote Play app that all is well abs. 100% I need to get my device on 10.0.66.10 to do a broadcast search on the 10.0.69.XXX subnet (or have a 10.0.69.XXX address).

I feel (hope) there is a way to do this, but I am no iptables wizard. Does anyone know how to accomplish this? The solutions linked don’t make sense to me in a practical way to apply them.

  • cooljimy84@lemmy.world
    link
    fedilink
    English
    arrow-up
    4
    ·
    1 year ago

    My friendly 2 pence, my mobile provider me a 10.x.x.x IP with CNAT (carrier grade NAT) when I’m on mobile data.

    Could you not set your subnet mask on the wireguard and home to 255.255.0.0 then you can see the whole 10.0.x.x block in a broadcast?

    • glizzyguzzlerOP
      link
      fedilink
      English
      arrow-up
      1
      ·
      1 year ago

      Where would I set the subnet mask?

      I do not understand how to apply most networking concepts effectively - I only run Opnsense to get a router that has actual software updates, not because I now how to use it (no experience with networking otherwise).

      In WireGuard I specify the 10.0.66.XX subnet directly without DHCP. In Opnsense, I’m not sure where to look and searching for it didn’t help illuminate anything obvious.

      • cooljimy84@lemmy.world
        link
        fedilink
        English
        arrow-up
        2
        ·
        edit-2
        1 year ago

        So the subnet mask is got from the device handing out dhcp. Not 100% sure but on my android the subnet mash for wireguard is as /24 set on the device and also matching in the wireguard settings in opnsense. Opnsense is very very powerful, I would watch a few videos on YouTube about subneting, wireguard routing & dhcp. Its gonna be quite the learning curve (or could be)

        As to why everything has stopped working who knows…

        • glizzyguzzlerOP
          link
          fedilink
          English
          arrow-up
          1
          ·
          edit-2
          1 year ago

          Who knows indeed, I’m beginning to suspect that it was able to connect via the internet (and that stopped working) and I just never noticed so the VPN was a superfluous extra step.

          But I did try in the [Peer] definition setting the allowed IPs to: 10.0.66.10/16 instead of 10.0.66.10/32, which should expand the allowed range to 10.0.69.XXX. Alas, that did not work.

          Edit: Also tried assigning the [Peer] to an unused IP in the 10.0.69.XXX range directly, but that made nothing work so not the way either.

          • cooljimy84@lemmy.world
            link
            fedilink
            English
            arrow-up
            3
            ·
            1 year ago

            Both devices need the same subnet mask, otherwise only one can see the “extra addresses” but in my opnsense I think I and to add some firewall router between LAN & WG0

            • glizzyguzzlerOP
              link
              fedilink
              English
              arrow-up
              2
              ·
              1 year ago

              Setting the WG [Interface] range to 10.0.66.0/16, along with the [Peer] to 10.0.66.10/16, and the Opnsense DHCP range in Interfaces->LAN to /16 made no connection to the internet or local occur.

              This feels like banging rocks together hoping for fire - not for me (but maybe reading stuff for a bit will help, maybe)

      • nrezcm@lemmy.world
        link
        fedilink
        English
        arrow-up
        2
        ·
        1 year ago

        Check your firewall logs (Status -> System Logs -> Firewall for pfSense, can’t remember for opnsense). I’d suspect you might see blocks from 10.0.66.x to your Playstation.

        • glizzyguzzlerOP
          link
          fedilink
          English
          arrow-up
          1
          ·
          1 year ago

          I don’t see any - but I guess it makes sense, the Opnsense computer isn’t involved by design in local network activity. The Opnsense comp goes to a switch that all other LAN also connect to, and I assume the switch routes so the Opnsense comp connection doesn’t get bottlenecked. I indeed forgot that’s how it worked till now - thanks for the suggestion, helped me internalize a bit more infrastructure at least!