• p_diablo@lemmy.world
        link
        fedilink
        arrow-up
        1
        ·
        1 year ago

        Is that an actual thing? I diy’d some of that by shoving a bunch of steel-wool into the foam while it was wet. Seems to have worked.

        • Draupnir@lemmy.world
          link
          fedilink
          English
          arrow-up
          1
          ·
          1 year ago

          That should work actually, we already know they don’t like steel wool so you’ve likely achieved the same effect

  • rouxdoo@kbin.social
    link
    fedilink
    arrow-up
    24
    ·
    1 year ago

    @SirNuke All of the comments saying spray foam are technically correct - that is the easiest way but it will look like orange crap. Some people mentioned steel wool - avoid that because it rusts and will end up looking like orange crap. Find some “excluder mesh”, which an inexpensive product sold to the pest control industry - it is a nylon mesh with reinforcing fibers…think Brillo pad stiffness. Stuff the gap to fill it then use silicone sealant to finish it off.

    • parrot-party@kbin.social
      link
      fedilink
      arrow-up
      11
      ·
      1 year ago

      I would say the expanding foam would still be preferred. Just don’t go crazy with it. Then before it’s fully cured, cut it back flush. Wait for it to dry then caulk to cover/seal.

      • rouxdoo@kbin.social
        link
        fedilink
        arrow-up
        5
        ·
        1 year ago

        @parrot@kbin.social

        @SirNuke

        My actual job is to inspect homes. It is an industry joke that Joe-diy-guy grabs a can of great-stuff expando foam and “fixes” it…leaving a jacked up mess that rats just chew through to get in again. There are better ways of securing entry points.

    • SirNuke@kbin.socialOP
      link
      fedilink
      arrow-up
      4
      ·
      1 year ago

      That’s a good suggestion, I was looking at stainless steel wool and wasn’t finding a lot of great options.

      • rouxdoo@kbin.social
        link
        fedilink
        arrow-up
        6
        ·
        1 year ago

        @SirNuke Another option if you don’t want to source excluder mesh is to get some “backer rod” - a painter’s product sold as “caulk saver” at the home improvement palace. You use it to fill large gaps which you then seal over with caulk or silicone.

      • rouxdoo@kbin.social
        link
        fedilink
        arrow-up
        2
        ·
        1 year ago

        @SirNuke The other reason to not use steel wool is that it can be a fire hazard. A low voltage shorted across steel wool will result in fire (I carry a 9-volt and steel wool in my camping kit as emergency fire-starter).

  • SirNuke@kbin.socialOP
    link
    fedilink
    arrow-up
    20
    ·
    edit-2
    1 year ago

    For context, this is leading to my AC unit. While hanging a light above my workbench, I noticed daylight coming in from the wall where there shouldn’t be any. It appears a previous owner had pulled back the insulation and forgot to put it back - shudder to think how much money that’s costed me over the last two years. Would like a hardier seal than insulation to stop water and mice, but not sure what is required.

    • Hyzerflip@lemmy.world
      link
      fedilink
      arrow-up
      18
      ·
      edit-2
      1 year ago

      Really depends on access. Can goy access it from the backside? Quick and easy, but a little messy, expanding foam.

      • HailHodor@lemmy.dbzer0.com
        link
        fedilink
        arrow-up
        36
        ·
        1 year ago

        Okay, I know that’s a typo, but I’m cracking up at the idea of you asking about unauthorized access by Jewish people.

      • SirNuke@kbin.socialOP
        link
        fedilink
        arrow-up
        6
        ·
        1 year ago

        It’s super awkward but I can get to it from inside the house (between insulation and hole). Going to have to move my workbench but so be it.

        Any direction on the type/brand of foam I should use? I have a can of fireblock to seal ethernet runs from my basement to main floor, though it’s probably seized up by now.

        • Hyzerflip@lemmy.world
          link
          fedilink
          arrow-up
          7
          ·
          1 year ago

          I would use fire block since normal expanding foam is flammable. If I could get behind it, I would see if the hole was excessively large and if so, cut a piece of OSB to fit the space with a hole the correct size in it. Then I would bisect the piece of OSB (making sure to bisect the hole) so that I would be able to get it around the cables and refrigerant line. If the hole isn’t excessively large, fire stop caulk the penetration and insulate the best you can.

          • Semi-Hemi-Demigod@kbin.social
            link
            fedilink
            arrow-up
            7
            ·
            1 year ago

            I’d pack some stainless steel wool around it before doing the expanding foam. This will prevent rodents from chewing through it, which they can do to the foam.

            They make rodent-blocking foam but I trust the steel wool more

            • WHARRGARBL@kbin.social
              link
              fedilink
              arrow-up
              4
              ·
              1 year ago

              Weighing in to emphasize the importance of packing it with steel wool before using fireblock. It’s a game changer.

            • 18Rabbit@lemm.ee
              link
              fedilink
              arrow-up
              3
              ·
              1 year ago

              We had a hole like that that mice kept coming through and steel wool + foam ended that problem.

  • pixel_witch@lemmy.world
    link
    fedilink
    arrow-up
    10
    ·
    1 year ago

    My first thought is great stuff but honestly I have only used it in a crafting context and I am sure someone else will have a better idea or be able to explain why my gut reaction is not going to work. Also could look ugly if the foam expands out of the hole though it can be cut off to be even once cured.

  • OnlyTakesAshot@lemmy.world
    link
    fedilink
    arrow-up
    10
    ·
    1 year ago

    Spray foam is generally what’s recommended. Be conservative with it though, it expands a lot and can push wires and cause other problems if you use too much.