You can use a boost converter to boost the 5V of an USB port to the 19V your notebook needs.

Assuming 5A output from a powerbank (which is probably about the max you will get without USB PD), you could theoretically get 0.55A at 19V. With the unavoidable inefficiencies, you will get less.

So, maybe enough to very slowly charge your notebook while it’s off. But when it’s turned on, the battery charge will still drop.

Sure, the skull is biodegradable. But didn’t you know that large-scale human farming is responsible for the vast majority of CO2 emissions?!

Right, I might just see what cooler I can get second-hand. Thanks for your input!

This seems to be a bug in the slicer. I’m seeing the same issue in OrcaSlicer if the skirt height is set to more than one layer (even if the skirt is disabled). This makes sense if a skirt is used (can’t print a continuous spiral if you have to switch between printing the object and the skirt), but not if it’s disabled.

What slicer are you using? If it’s a PrusaSlicer fork, this is likely the same bug.

It looks to me like a JST SH connector: https://www.sparkfun.com/products/retired/10357

Measure the distance between the two pins - if it is 1 mm, this is most likely the connector you’re looking for.

From a cursory read of the datasheet, using the “dead time control” pin seems to be the way to go. Basically, this pin is used to set the voltage, while the error amplifier inputs (that’s the closest function to “over current protection” this chip has) are used to adjust the output according to the load. For your application, you probably don’t need to use them at all.

My instinct would be to disable the error amplifiers by connecting pins 1,2,15 and 16 to GND. You can then connect the wiper pin of the potentiometer to the deadtime control input, with the other pins of the potentiometer connected to GND and 3.3 V.

I haven’t worked with this chip before, so take this with a grain of salt. You should probably use a simulation tool to check the circuit before you start destroying chips.

You can bring the resting position of the brake lever closer to the handlebar by turning this screw clockwise. The brake lever looks a bit short for my taste, it’s probably not designed for use with that type of shifter. But with a bit of adjustment it should still be usable.

Do you expect every meme to be meticulously handcrafted? It’s a stupid joke, not a work of art.

Close, but the word ends in -le, not -ie. The -le suffix is used as a diminutive form in some German dialects.

A small pair of vernier calipers. I don’t use them a lot, but sometimes they come in very handy.

Unfortunately, this might not be easy to find a solution for. The larger thread size doesn’t seem to be a standard bike pedal thread, so finding a specific adapter is probably not possible.

Another solution might be to use some kind of threaded inserts in the cranks (this would probably require drilling the cranks out for a larger thread). But the standard pedal thread of 9/16-20 is not widely used anywhere else, so finding the inserts (let alone a left-handed ones is probably next to impossible.

Klar hinterlässt das Spuren, aber nichts was man mit etwas Seife oder Spüli nicht wieder weg kriegt. Der Dreck ist ja in dem Moment schon gelöst (sonst wäre er noch am Fahrrad). Nur Festtrocknen würde ich es nicht lassen.

Ich wäre nur vorsichtig dabei, mit höherem Druck direkt an die Lager ran zu gehen. Danach hast du sonst auch Wasser in den Lagern und musst doch alles auseinander bauen und neu fetten.

My router is called Jupiter, everything connected to it is named after a moon. Callisto, Ganymede, Thelxinoe, Kallichore are what I’m currently using.

IIRC, this is actually done at some point in the books.

You can host a Firefox sync server yourself. You could run that on something like a Raspberry Pi in your local network. If you need remote access, use something like cloudflare tunnels (although I guess that’s something else to be paranoid about).

Windows is clearly superior. If you’ve had enough of the settings app, you can just switch to the control center!

Reminds me of this: Falsehoods Programmers Believe About Names

Interesting! Turns out I’ve been doing parallel view all along. I was wondering why some of the images posted here look a bit weird to me - looking back, the ones that work for me are actually for parallel viewing.

What did you expect? We’re talking about one guy who might have lived over 2000 years ago. You’re not going to find his birth certificate and social security number.

The best anyone can do is assign a probability to his existence. And reading the article you yourself linked to, that probability seems to be pretty high.

Sorry dass ich nichts hilfreicherws beizutragen habe, aber der Janosch passt hier einfach zu gut:

Herr Janosch, schwere Entscheidungen, wie trifft man die? “Man schreibt die Alternativen tabellarisch auf einen Zettel. Anschließend legt man den Zettel nieder und wirft einen Löffel auf den Zettel. Dann geht man weg und lässt den Löffel das regeln. Sein Problem.”